The short answer
A Bitcoin mining container is a shipping-container-sized enclosure that packs miners, power distribution and cooling into one unit you can drop onto a prepared site and energize. Rather than build a room full of racks, you ship the room. Bitmain's ANTSPACE HK3 V6, the worked example used throughout this guide, holds 210 hydro-cooled miners inside a box measuring 6058 x 2438 x 2896 mm and draws a little over a megawatt when it's running.
What a Bitcoin mining container actually is
Picture a standard 40-foot shipping container. Now fill it with mining hardware, a power distribution cabinet, and the plumbing that moves heat out of the box. That's the idea behind a Bitcoin mining container, sometimes called a bitcoin mining shipping container or a bitcoin mining rig container. The form factor matters because it makes a site deployable: the unit is built and tested in a factory, trucked to location, lifted into place with a crane, and connected to power and a cooling loop.
This is a very different thing from running a few machines in a spare room. A single container is sized for utility-scale power, and it comes with the switchgear and safety systems that a room full of loose miners usually lacks. If you are weighing the home route instead, the trade-offs are covered in running miners at home.
The ANTSPACE HK3 V6 is a hydro container, meaning the miners inside are liquid-cooled rather than air-cooled. That choice shapes almost everything else about the design, from the plate heat exchanger to the cooling tower that sits alongside it.
Inside the ANTSPACE HK3 V6: a worked example
Here are the headline figures from Bitmain's spec page. These are the manufacturer's typical values, not independently measured results, so treat them as the maker's own numbers.
| Specification | ANTSPACE HK3 V6 |
|---|---|
| Outer dimensions (L x W x H) | 6058 x 2438 x 2896 mm |
| Miner capacity | 210 units, S19 Hyd. and S21 Hyd. series |
| Operating power | 1047 to 1050 kW |
| PUE | 1.022 excluding cooling tower, 1.032 including tower |
| Input voltage and frequency | 400V plus or minus 5%, 50/60 Hz |
| Rated current | A: 952 A, B: 866 A |
| Rated current per miner | 10 A |
| Cooling flow rate | greater than 85 m³/h |
| Operating weight | 12 tonnes |
- ANTSPACE HK3 V6
- 6058 x 2438 x 2896 mm
- ANTSPACE HK3 V6
- 210 units, S19 Hyd. and S21 Hyd. series
- ANTSPACE HK3 V6
- 1047 to 1050 kW
- ANTSPACE HK3 V6
- 1.022 excluding cooling tower, 1.032 including tower
- ANTSPACE HK3 V6
- 400V plus or minus 5%, 50/60 Hz
- ANTSPACE HK3 V6
- A: 952 A, B: 866 A
- ANTSPACE HK3 V6
- 10 A
- ANTSPACE HK3 V6
- greater than 85 m³/h
- ANTSPACE HK3 V6
- 12 tonnes
A few of these deserve a word. PUE, or power usage effectiveness, measures how much extra energy the facility burns on top of the miners themselves. A PUE of 1.032 including the tower means the overhead is about 3.2%, which is low and is what liquid cooling buys you. Bitmain lists an operating weight of 12 tonnes for the unit, so the pad it sits on needs planning.
How the cooling loop works
Hydro miners run hot water out of the machines and need somewhere to dump that heat. In this system the chain runs from the miners, through a titanium plate heat exchanger, out to a dry-wet cooling tower. The heat exchanger is a compact unit, roughly 775 x 480 x 1069 mm, with an internal circulation flow rate of 100 m³/h and an external loop running 33 to 110 m³/h.
The dry-wet tower is rated to shed 1000 kW of heat and holds an outlet temperature of 35°C at a 28°C wet-bulb temperature. It sips water at 0.7 to 1.3 m³/h and runs at about 70 dBA measured 15 m away, which is roughly the volume of a busy road. There is also a dry-tower option that uses no evaporative water but has a tighter temperature margin, holding 35°C only when the ambient air is around 30°C.
The miners themselves set the rules for the loop. Bitmain's S21 XP Hyd, a current hydro model, wants inlet water between 20 and 50°C and a flow of 8 to 10 litres per minute per machine. If the inlet water drops below 20°C, the miner will not start, so the cooling design has to keep water warm enough as well as cool enough. Fluid chemistry matters too: the spec calls for deionized or pure water with antifreeze, kept in a narrow pH band.
Power, current and the transformer
A container this size is a serious electrical load. The HK3 V6 takes 400V three-phase at 50 or 60 Hz, with rated currents of 952 A on one bus and 866 A on the other, and a main switch arrangement listed as 1200 A times two. Each miner pulls about 10 A. The inlet cables are heavy, specified to withstand more than 600V, with multiple 300 mm² single-core runs per phase.
On the upstream side, Bitmain references a 2500 kVA transformer to feed the containers, though the spec page leaves the exact number of containers per transformer blank, so that figure needs confirming with the supplier rather than assumed. Getting the transformer, the switchgear, and the grounding right is not optional, and it is one of the line items a quote has to spell out.
Wrong input voltage can damage the miners, per Bitmain's own warning, so the electrical design has to be signed off before anything is energized.
What the hashrate math looks like
People naturally want to know how much mining power a full container represents. You can get an illustrative figure by multiplying capacity by a per-miner hashrate, but read the caveat first.
The S21 XP Hyd is rated at 473 TH/s. If you filled all 210 slots with that model, the arithmetic is:
210 x 473 TH/s = 99,330 TH/s, or about 99.3 PH/s.
That is an illustration only, calculated on 2026-11-18 from the two spec sheets. The HK3 V6 page names the S19 Hyd and S21 Hyd series in general, not the S21 XP specifically, so a real build could use a different hydro model with a different hashrate. The container's rated operating power of 1047 to 1050 kW also points to a less power-hungry mix than 210 units of the 5676 W XP would draw, which is another reason to treat the number as a ceiling-of-the-envelope estimate rather than a spec. To sanity-check any real configuration, plug the actual model into a mining calculator, and if the units themselves are unfamiliar, the hashrate explainer covers what TH/s and PH/s mean.
What does a Bitcoin mining container cost?
Here the honest answer is that we found no published list price for the ANTSPACE HK3 V6, and we are not going to make one up. What exists is a cost range at the facility level. The Cambridge Digital Mining Industry Report estimates infrastructure capital expenditure for Bitcoin mining at $0.24 million to $1.2 million per megawatt. That is the report's own analysis, it covers hardware plus build, and the spread reflects the gap in ASIC market prices between more and less efficient machines.
Applied to a single roughly 1.05 MW container, that range implies something like:
1.05 MW x $0.24 million = about $0.25 million, up to 1.05 MW x $1.2 million = about $1.26 million.
That is an illustration at 2026-11-18 using only the report's per-MW range and the container's operating power. It is not a container list price, and the real number depends heavily on which miners go inside and when they are bought. Because there is no sticker price, any figure you see quoted should be requested as a written quote. A useful quote spells out the answers to questions like these:
- Does the price include the container itself, or the miners separately?
- Is the cooling tower included, and which type?
- Is a transformer in scope, or is that on you?
- What does delivery and crane offload cover?
- Who handles commissioning and startup?
- What warranty applies, and for how long?
Treat each of those as a question to get answered in writing, not a fact you can assume.
Siting, certifications and sourcing questions
Where a container goes is as important as what it costs. Bitmain's points for attention are blunt about the groundwork: the tower must sit on flat ground level to within one degree, the surface has to be hardened to hold at least 25 tonnes, and the customer needs a 20-tonne crane to load and unload the units. Stairs, walkways, transformers, cables and distribution boxes are listed as things the buyer prepares.
The bigger constraint is often the site itself. The Cambridge report found that insufficient hosting capacity, and the lack of new hosting development, were seen as major barriers to growth, while power availability was less of a worry. About 44.7% of respondents viewed power availability as at most a low constraint. The bottleneck, in the report's words, is the availability of brownfield sites: operational facilities with existing hosting capacity that can energize new equipment straight away. So one of the first sourcing questions is not "can I buy a container" but "do I have a site that can host it."
On safety, the HK3 V6 page lists certifications including NFPA 79:2021, UL 508A:2018 R8.21, CSA C22.2 No. 14-18, ANSI/ISO 12100:2012 and IEC 60204 Ed 5.1 2009, plus China Classification Society certification for the container. When you talk to a supplier, worth confirming which certifications apply in your jurisdiction, what input voltage and frequency the unit is wired for, and exactly how the cooling loop connects to your site.
Is a container realistic for most people?
For almost everyone reading this, the straight answer is no, and that is fine to say. A 1 MW container is industrial infrastructure. It needs a transformer, a hardened pad, a crane, a water loop, and a power contract, and the capital range above runs from a quarter of a million dollars into the millions before the first bitcoin is mined. That is a world away from plugging a single machine into a wall socket at home.
If the appeal was exposure to mining without owning and running hardware, that is a different path with its own trade-offs and risks, and nothing here promises a profit. A plain starting point is what cloud mining is, and the cloud mining costs page walks through where the money actually goes. Containers are built for operators who already have land, power and a crew. Knowing that upfront saves a lot of wasted quote requests.
Frequently asked questions
What is a Bitcoin mining container?
It is a shipping-container-sized enclosure that holds miners, power distribution and cooling in one deployable unit. The Bitmain ANTSPACE HK3 V6, for example, fits 210 hydro-cooled miners in a box measuring 6058 by 2438 by 2896 mm.
How many miners fit in one container?
The ANTSPACE HK3 V6 is rated for 210 units from the S19 Hyd and S21 Hyd series, all liquid-cooled. The container draws 1047 to 1050 kW of operating power at that capacity, which is why it needs utility-scale electrical and cooling infrastructure.
How much does a Bitcoin mining container cost?
We found no published list price. The Cambridge Digital Mining Industry Report estimates mining infrastructure capital expenditure at 0.24 to 1.2 million dollars per megawatt, covering hardware plus build. Any specific container price should be requested as a written quote.
Do Bitcoin mining containers need water?
Hydro containers like the HK3 V6 do. They run a liquid loop through a plate heat exchanger to a cooling tower. The dry-wet tower uses 0.7 to 1.3 cubic metres of water per hour, while a dry-tower option avoids evaporative water use.
Is a mining container practical for a home miner?
Generally no. A container is around a megawatt of industrial load needing a transformer, a hardened pad, a crane and a power contract. Home miners are far better suited to single machines, and those wanting exposure without hardware can look at cloud mining instead.
Related guides
Sources
- Bitmain Support, ANTSPACE HK3 V6 specifications (accessed 2026-11-18)
- Bitmain Support, Antminer S21 XP Hyd specification (accessed 2026-11-18)
- Cambridge Centre for Alternative Finance, Cambridge Digital Mining Industry Report, April 2025 (accessed 2026-11-18)