Bitcoin Cloud Mining

Best Bitcoin Mining Hardware for Cheap Power Sites

Compare the Antminer S21, S21 XP Hyd and S21 Imm by efficiency, wall power and cooling needs, and see why power price rules a cheap-power site.

Updated 2026-11-18

The short answer

For a cheap-power site, the hardware choice comes down to matching a miner's efficiency and cooling to what your site can supply and reject as heat, not only to the lowest J/TH. Among the three Bitmain models compared here, the S21 XP Hyd is the most efficient at 12.0 J/TH, but it uses liquid cooling and three-phase power, while the air-cooled S21 at 17.5 J/TH runs on a single AC input. Because electricity is more than 80% of a miner's cash costs, the watts a machine saves and the price you pay for them weigh heavily on the result.

Why power price does most of the work

At a low power price, the lowest J/TH you can buy still carries weight, because the Cambridge Digital Mining Industry Report found that direct electricity made up 81.1% of miners' cash operating costs, with everything else (SG&A and cost of goods sold) adding up to the remaining 18.9%, or about $10.5/MWh. The report puts the median reported electricity cost at $45/MWh and the all-in figure at $55.5/MWh, based on survey data as of 30 June 2024.

The spread matters too. Reported hosting and direct rates ran from $25/MWh to $70/MWh, so two operators buying the same miner can end up with very different outcomes. Cambridge also noted that Bitcoin mining gross margins swung from 13% to 83% depending on market conditions, equipment efficiency and power cost. None of that is a promise about your site. At a low power price, the efficiency of the hardware and the rate you actually pay together carry the economics, so the cooling method you can run and afford becomes a central factor.

What J/TH means in plain terms

J/TH is joules per terahash: how much energy a miner burns to compute one trillion hashes. Lower is better, because it means more work for each watt. You can read it straight off the wall figures. The air-cooled S21 draws 3,500 watts to produce 200 TH/s, and 3,500 divided by 200 is 17.5 J/TH. Do the same for the hydro model and 5,676 watts over 473 TH/s gives 12.0 J/TH, which is why it is the efficient one of the group.

Here is how the four operating points rank, best to worst: the S21 XP Hyd at 12.0, the S21 Imm in its lower mode at 16.0, the air-cooled S21 at 17.5, and the S21 Imm in its higher mode at 18.5. For context, Cambridge estimated the weighted efficiency of hardware already in service at 28.2 J/TH, a 24% year-on-year improvement, so all four of these are well ahead of the installed average. If the term hashrate is new to you, the hashrate explained guide walks through the units.

The three Bitmain models side by side

The table below collects the manufacturer's typical values. The S21 Imm is one chassis with two working modes, so it appears twice. Dimensions are length by width by height without packaging.

Model and coolingHashrate (TH/s)Wall power (W)J/THInput powerSize w/o package (mm)Net weight (kg)Key environment limit
Antminer S21, air-cooled2003,50017.5220 to 277 V, single AC input, 20 A, 47 to 63 Hz400 x 195 x 29015.4Air 0 to 45°C, altitude ≤2,000 m
S21 XP Hyd, liquid-cooled4735,67612.0380 to 415 V, three-phase, 12 A, 50 to 60 Hz339 x 173 x 20713.8Inlet water 20 to 50°C, flow 8 to 10 L/min
S21 Imm (NEM), oil-immersion2393,82416.0380 to 415 V, 12 A, 50 to 60 Hz293 x 236 x 36417.15Inlet oil 30 to 55°C, altitude ≤2,000 m
S21 Imm (HEM), oil-immersion3015,56918.5380 to 415 V, 12 A, 50 to 60 Hz293 x 236 x 36417.15Inlet oil 30 to 55°C, altitude ≤2,000 m
Model and coolingAntminer S21, air-cooled
Hashrate (TH/s)
200
Wall power (W)
3,500
J/TH
17.5
Input power
220 to 277 V, single AC input, 20 A, 47 to 63 Hz
Size w/o package (mm)
400 x 195 x 290
Net weight (kg)
15.4
Key environment limit
Air 0 to 45°C, altitude ≤2,000 m
Model and coolingS21 XP Hyd, liquid-cooled
Hashrate (TH/s)
473
Wall power (W)
5,676
J/TH
12.0
Input power
380 to 415 V, three-phase, 12 A, 50 to 60 Hz
Size w/o package (mm)
339 x 173 x 207
Net weight (kg)
13.8
Key environment limit
Inlet water 20 to 50°C, flow 8 to 10 L/min
Model and coolingS21 Imm (NEM), oil-immersion
Hashrate (TH/s)
239
Wall power (W)
3,824
J/TH
16.0
Input power
380 to 415 V, 12 A, 50 to 60 Hz
Size w/o package (mm)
293 x 236 x 364
Net weight (kg)
17.15
Key environment limit
Inlet oil 30 to 55°C, altitude ≤2,000 m
Model and coolingS21 Imm (HEM), oil-immersion
Hashrate (TH/s)
301
Wall power (W)
5,569
J/TH
18.5
Input power
380 to 415 V, 12 A, 50 to 60 Hz
Size w/o package (mm)
293 x 236 x 364
Net weight (kg)
17.15
Key environment limit
Inlet oil 30 to 55°C, altitude ≤2,000 m

A few points stand out. The air-cooled S21 runs on a single AC input at up to 277 volts. Both the hydro and the immersion machines use three-phase 380 to 415 volt input, so your electrical design has to suit that. Wrong input voltage can damage the server on every one of these models, which Bitmain flags in its own notes.

Air-cooled, hydro, or immersion: what each choice asks of your site

The cooling method affects your build cost and your site constraints, so it deserves attention alongside the J/TH figure.

The air-cooled S21 has an ambient operating range of 0 to 45°C, non-condensing humidity of 10 to 90%, and an altitude at or below 2,000 meters. Bitmain adds that from 900 meters up, the highest operating temperature drops by 1°C for every extra 300 meters of altitude.

The S21 XP Hyd is the liquid-cooled model. It needs an inlet water temperature of 20 to 50°C, a flow of 8 to 10 liters per minute, water pressure at or below 3.5 bar, and a working fluid of deionized or pure water with antifreeze held at a pH of 8.5 to 9.5. The miner will not start if the inlet water is below 20°C, so you cannot simply pipe in cold water. Bitmain pairs it with an external dry cooler, the EC2-DT, and ties the ambient limit to the outlet water temperature: at a 35°C outlet the maximum ambient is 30°C, at 45°C it is 40°C, and at 50°C it is 45°C.

The S21 Imm drops into a dielectric oil bath and needs an inlet oil temperature of 30 to 55°C, with the same altitude ceiling of 2,000 meters and the same 1°C per 300 meter derating above 900 meters as the air-cooled unit. It has two working modes. Normal Energy Mode runs at 239 TH/s and 16.0 J/TH, while High Energy Mode runs at 301 TH/s and 18.5 J/TH, the highest J/TH figure in this group.

Typical values, not guarantees

Every number above is a manufacturer typical value, which is not the same as a measured guarantee for the unit on your bench. For the S21 XP Hyd and the S21 Imm, Bitmain states that the actual hashrate fluctuates by plus or minus 3%, and that the actual wall power and efficiency fluctuate by plus or minus 5%. The wall figures are also quoted at a reference temperature, 25°C for the air-cooled S21, 35°C for the hydro, and 30°C for the immersion unit.

What this means for planning is simple. Size your electrical feed and your cooling with a little headroom above the nameplate, because a 5% swing on a 5,676 watt machine is roughly 284 watts, and that adds up across a room full of them. Treat the spec sheet as a center point, not a ceiling.

An illustrative daily energy cost

Here is a worked example, labeled as an illustration at today's date, 18 November 2026. It uses only the air-cooled S21's typical numbers, and the power prices below are examples, not quotes for any site.

Start with the wall power: 3,500 watts, which is 3.5 kilowatts. Over a full day that is 3.5 kW multiplied by 24 hours, or 84 kilowatt-hours per machine per day. At an example rate of $0.03 per kWh, the energy cost is 84 kWh multiplied by $0.03, which comes to $2.52 per day. If instead you apply Cambridge's reported median electricity cost of $45/MWh, which is $0.045 per kWh, the same 84 kWh works out to $3.78 per day. Over 30 days those examples become about $75.60 and $113.40 respectively.

This is energy cost only. It says nothing about what the machine earns, which depends on network difficulty, the Bitcoin price and the fees of the moment, and it carries no promise of profit. To plug in your own numbers against live network figures, the mining calculator is the place to do it rather than trusting any single illustration.

What the hardware itself costs, roughly

We could not source current ASIC prices, so none are quoted here. Cambridge does give a site-level capital estimate: it puts the hardware CAPEX for Bitcoin mining at a range of $0.24 to $1.2 million per megawatt, which the report describes as its own analysis and an estimate that reflects the gap in ASIC prices between more and less efficient devices. Read that as a planning band for a whole megawatt of capacity, not a sticker price for any one miner.

With power making up more than 80% of running cost, the economics of a cheap-power site rest on efficient, well-matched hardware and a low electricity rate. The three machines here are all Bitmain. Other manufacturers such as Whatsminer and Canaan also build SHA-256 miners, but they are not compared here because current spec pages for them could not be sourced for this guide, so no figures are given for them.

If running machines is not for you

Everything above is operator-level hardware. It assumes you can arrange three-phase power, a dry cooler or an oil loop, and the space and electrical work that go with them. That is a real project, and not everyone wants it.

If you would rather not run machines yourself, the alternative is paying someone else to run capacity on your behalf, which shifts the questions from amps and coolant to contract terms and fees. Our plain explainer on what cloud mining is covers how that model works, and the cloud mining costs page breaks down the fees that tend to decide whether it makes sense. If you are weighing a home setup instead, Bitcoin mining at home looks at the practical limits of running one or two units in a house.

Frequently asked questions

Which Antminer in this comparison is the most efficient?

Of the three, the S21 XP Hyd is the most efficient at 12.0 J/TH, followed by the immersion S21 in NEM mode at 16.0, the air-cooled S21 at 17.5, and the immersion S21 in HEM mode at 18.5. Lower J/TH means more work per watt.

Does a lower J/TH always mean a lower cost at a cheap-power site?

Not on its own. Efficiency sets how many watts you burn per terahash, but cooling hardware, three-phase power and site limits add cost and complexity. A simpler air-cooled unit can suit a site that cannot support liquid loops or dry coolers.

Can the S21 XP Hyd run without a dry cooler?

Bitmain lists the external EC2-DT dry cooler for the S21 XP Hyd, with ambient limits tied to outlet water temperature. The miner also will not start if inlet water falls below 20 degrees Celsius, so some heat-rejection loop is needed to run it.

What is the difference between NEM and HEM on the S21 Imm?

NEM is Normal Energy Mode and HEM is High Energy Mode. In NEM the S21 Imm runs at 239 terahash and 3,824 watts; in HEM it runs harder at 301 terahash and 5,569 watts, with efficiency slipping from 16.0 to 18.5 J/TH.

How much power does an air-cooled S21 use per day?

At its typical 3,500 watts, an air-cooled S21 draws about 84 kilowatt-hours over 24 hours. That figure is manufacturer-rated and can fluctuate, and the dollar cost depends entirely on the power price your site actually pays for electricity.

Related guides

Sources