The short answer
Immersion cooling means fully submerging a Bitcoin miner, the hardware that runs the mining, in a non-conductive liquid that carries heat away instead of blowing air across the components. This fluid, called a dielectric, soaks up heat from the chips and power parts and moves it to a heat exchanger, so the usual cooling fans are no longer needed.
How it works
Air cooling blows chilled air over the boards and relies on fans in each unit. Immersion cooling drops the whole machine into a tank of dielectric fluid instead. The arXiv preprint "Enough Hot Air" describes this fluid as one that conducts heat but not electricity, so it can sit against live components and pull their heat straight into the liquid. A pump moves the warm fluid to a heat exchanger, and the cooled fluid returns to the tank. The preprint says immersion allows much higher power per rack than air cooling.
Two setups exist. Single-phase keeps the fluid liquid the whole time. Two-phase lets it boil and condense, which the preprint links to some of the lowest reported numbers.
Why miners run it
The usual reason is heat removal and a lower PUE. PUE is total facility energy divided by the energy that reaches the IT gear, so a number near 1.0 means almost everything goes to hashing. The arXiv preprint reports immersion-cooled data centers landing close to 1.02 to 1.04, with 1.02 as the common sweet spot and a maximum reported figure of 1.17; one single-phase deployment it cites cut total power by 36% and reached 1.07. Air-cooled sites, by contrast, span roughly 1.1 to 2.9 in the same paper, where the low end near 1.1 is reached only by hyperscale facilities and average sites run much higher, between 2.2 and 2.61 in the locations it surveyed. The Uptime Institute reports most direct liquid cooling reaching a partial PUE of 1.02 to 1.03, and notes that submerged machines drop the IT fans that otherwise draw an estimated 5% to 10% of IT power depending on fan efficiency, size and speed.
Reading the S21 Imm numbers
Bitmain's S21 Imm is an immersion-cooled model, and its spec sheet lists two modes. In Normal Energy Mode (NEM) it gives a typical 239 TH/s at 3,824 watts, or 16.0 J/TH. In High Energy Mode (HEM) it pushes to 301 TH/s at 5,569 watts, or 18.5 J/TH. These are the maker's typical values; Bitmain says hashrate can swing by 3% either way and power by 5%. The sheet also sets an inlet oil temperature of 30 to 55°C, the window the warm fluid should sit in as it enters the tank.
The trade-offs
The same preprint is blunt about the downsides. The preprint names maintenance and an increased number of IT failures among the main downsides. It also warns that retrofitting an existing air-cooled site for immersion runs up high costs and generally isn't worth it. So the gains in energy use and density come paired with service and reliability questions. For how cooling choices feed into the wider bill, see cloud mining costs, and for a fuller walk-through read the guide on immersion cooling for Bitcoin mining. More terms sit in the glossary.
Frequently asked questions
Does immersion cooling use water?
No. The machine sits in a dielectric fluid, which carries heat without conducting electricity. The warm fluid then passes its heat on through a heat exchanger. Bitmain's S21 Imm sheet describes the liquid as oil.
What PUE does immersion cooling reach?
The arXiv preprint reports immersion-cooled data centers near 1.02 to 1.04, with 1.02 as a common sweet spot. The Uptime Institute reports most direct liquid cooling at a partial PUE of 1.02 to 1.03.
What is High Energy Mode on the S21 Imm?
It is Bitmain's higher-output setting. In High Energy Mode the S21 Imm runs a typical 301 TH/s at 5,569 watts, against 239 TH/s at 3,824 watts in Normal Energy Mode. The higher mode gives more hashrate at a higher power draw.
Related guides
Sources
- Enough Hot Air: The Role of Immersion Cooling (arXiv preprint 2205.04257) (accessed 2026-11-18)
- Does the spread of direct liquid cooling make PUE less relevant? (Uptime Institute) (accessed 2026-11-18)
- S21 Imm Specifications (Bitmain Support) (accessed 2026-11-18)